Chapters / How nuclear power works
How nuclear power works
Fission, chain reactions and the fuel cycle: what happens inside a reactor, at the level of a physics textbook.
Every operating commercial reactor makes electricity the same indirect way: nuclear fission heats water, steam turns a turbine, the turbine turns a generator. The nuclear part ends at heat. Everything after the steam generator would be familiar to a coal-plant engineer.
The physics underneath is well understood and openly published. A uranium-235 nucleus absorbs a neutron, becomes unstable, and splits into two lighter nuclei, releasing energy and two to three more neutrons. If at least one of those neutrons goes on to split another nucleus, the reaction is self-sustaining: a chain reaction. Control rods of neutron-absorbing material and the moderator that slows neutrons down are what keep the reaction steady rather than runaway.
Fission and the chain reaction
Uranium-235 is the workhorse because it is fissile: a slow (thermal) neutron can split it at any energy it arrives with. Each fission releases about 200 MeV of energy, carried mostly by the two fission fragments, plus two to three free neutrons. When the geometry and materials let at least one neutron per fission, on average, cause another, the reaction is self-sustaining; reactors call that state critical, which simply means steady, not dangerous. Natural uranium is only about 0.7 per cent U-235; almost all the rest is U-238, which mostly absorbs neutrons without fissioning at thermal energies. [iaea-science]
From heat to electricity
In a pressurised-water reactor, the most common type, the core heats water kept liquid under high pressure; that water passes its heat to a secondary loop in a steam generator, and the secondary steam drives the turbine. A third loop, often with cooling towers, condenses the steam back to water. Boiling-water reactors skip the middleman: the core's own steam goes to the turbine. Either way, the reactor is a heat source; the rest of the plant is conventional steam engineering. [nrc-science101]
Keeping the reaction steady
Fast neutrons fresh from a fission are poor at splitting U-235; a moderator (ordinary water in most power reactors, graphite or heavy water in others) slows them to thermal energies where fission is hundreds of times more likely. Control rods of neutron-absorbing material set the power level and can shut the reaction down in seconds. The physics adds a stabiliser: in water-moderated designs, if the core overheats the water expands or boils, moderation falls, and the reaction rate drops on its own, a negative feedback that most (not all) reactor types enjoy. [nrc-science101] [iaea-science]
The fuel cycle in brief
The front end runs: mining and milling to uranium concentrate (yellowcake), conversion, enrichment from the natural 0.7 per cent U-235 to the 3-5 per cent typical of light-water reactor fuel, and fabrication into ceramic pellets stacked in metal-clad rods bundled into assemblies. After several years in the core the fuel is spent: intensely radioactive and thermally hot, it goes first to a cooling pool at the plant, then either to dry storage casks or, in countries that reprocess (France, Russia, Japan, India and others), to separation of reusable uranium and plutonium from the waste stream. Most of the world's spent fuel is stored, not reprocessed. [wna-fuelcycle]
Enrichment, at capability level
The same isotope physics underlies power and weapons, which is why enrichment sits at the centre of non-proliferation. Reactor fuel needs only a few per cent U-235; weapons designs call for highly enriched uranium, conventionally 90 per cent or more. The technical effort is concentrated in the early stages of raising the assay, so the line the safeguards system watches is at the low end. This encyclopedia keeps the discussion at this capability level: what the thresholds are and why they matter, never how the separation is done. [wna-fuelcycle]
Decay heat: the accident that never sleeps
Shutdown stops the chain reaction, not the heat. Freshly used fuel contains hundreds of short-lived fission products that keep decaying, releasing around 6 per cent of the reactor's operating heat in the first seconds after shutdown, roughly 1 per cent after a day, and less thereafter. That residual heat is small but not optional: without continuous cooling it can melt the core, which is precisely the sequence behind Three Mile Island and Fukushima. Nearly every safety system on a modern plant exists, in the end, to keep decay heat covered. [nas-fukushima] [nea-fukushima]
Still to come in this chapter
- Spent fuel management in depth: pools, casks, reprocessing chemistry at policy level, geological disposal (Onkalo and successors)
- The energy-density comparison, sourced: why a fingertip of uranium matches a tonne of coal
- Breeding and the closed fuel cycle, concept level (cross-referenced to the India chapter)